![]() The LED unit’s battery should last for approximately eight hours. To deactivate the Alpha-Brite system, remove the nock and LED unit, and pull the lighted end of the LED unit until the light turns off. ![]() When you fire your crossbow, the bowstring’s force will compress the two pieces, eliminate the gap, and activate the LED unit. Then, insert the nock tabs between the receiver’s locking clips until you hear/feel it “click” into place. To complete the Alpha-Brite installation, insert the LED unit – lighted end first – into the open end of the Alpha-Brite nock and insert the nock and LED unit into the Nock Receiver. ![]() The Nock Receiver is glued into the nock-end of the arrow and indexed with the vanes. The three-piece, Alpha-Brite Lighted Nock System begins with a Nock-Receiver insert designed to accept a combined LED unit and translucent pegged Alpha-Brite nock. Replacement Alpha-Brite Lite Stick with 8-10 hour battery life. This easy-to-use system activates the light when the arrow is fired, making it easier to track your shot and/or find your arrow on pass-through shots or missed. Image not available for Colour: To view this video, download Flash Player VIDEOS 360° VIEW IMAGES 2.0 Lighted 20' 2219 Aluminum Crossbow Arrows. There is a little dimple in the alpha nock that has to be lined up with cock vane.Tenpoint Alpha-Brite 2.0 Lite Stick (3 pack) TenPoint Omni-Brite 2 Lighted 20' Pro Elite Car 6 HEA-638.6 Merchant Video. The alpha nock can only go in reciever one way. You can install the omni in reciever any way. There is only one thing i like about the omni over the alpha nock. Time will tell if i stick with the plastic alpha nock. I know the alpha was designed for the crossbows with more of an acute angle on string. I changed do to it being the newest technology from ten point. I have been getting about the same accuracy with the alpha nock as the omni nock. The alpha is gonna be the replacement because of more nock to string contact. I believe I read that ten point was gonna stop manufacturing the omni nock. I'm getting 16 grain on the scale for plastic alpha and plastic omni. I started shooting the plastic alpha nock this year over the omni nock. I think Pin is referring to the aluminum alpha nock weight compared to the plastic alpha nock. The Omni-Nock design features six micro-grooves that form three bowstring channels which eliminate the indexing problem associated with moon and capture nocks. 305 ID) The three-piece, patent pending Omni-Brite 2. TenPoint’s patented Omni-Brite Nock makes other nocks obsolete when it comes to your arrow. The grooves in an Omni nock are not as deep as in a 1/2 moon nock.Ī slight modification on Barnett crossbows can easily correct this downward pressure problem on theĬrossbow that has the riser on the front of the rail-stock. Omni-Brite 2.0 Universal Lighted Nock System (f/.300. Using Omni or flat nocks on a Barnett, due to this error, the bow string could go under the arrow, TenPoint Crossbows Omni-Brite 2.0 LighAluminum Crossbow Arrows (3 Pack) (HEA-038.3) Amazon UK. If the riser was built to sit a wee bit higher, this would eliminate this problem. Properly manufactured, the bow string should have little to no downward pressure on the rail-stock. Shorter, lighter arrows, the front of the arrow may lift off the rail-stock near the riser end. Over time, these grooves will move up into the carbon arrow shaft. Rear of the arrow nock (not centering) which will eventually cause wear grooves in the nock where ![]() Due to the extreme downward pressure, the bowstring presses down on the This put extreme downward pressure on the bow string serving,Ĭausing undo wear. In the uncocked position, if you look from one cam to the other along the bow string, it humps The plastic arrow retainer and the brush retainer In a safe direction and give the stock a sharp wrap. Worst yet, fall out if the loaded crossbow is tilted at a downward angle. The arrow retainer or brush retainer if properly set up the arrow will not slide forward or If you look where the arrow retainer makes contact with the arrow, it is well forward of the arrow The rail-stock where the arrow lays was not wide enough.Īnother thought was the arrow retainer was putting too much pressure on the back of the arrow. The bowstring when the crossbow is cocked and loaded. Barnett states to use the 1/2 moon nock.īarnett crossbows have a manufacturing problem where the arrow nock does not center on I would not advise using these in a Barnett crossbow. : Omni Brite Nocks 1-48 of 100 results for 'omni brite nocks' Results Price and other details may vary based on product size and color. The advantage of an Omni nock providing it is installed correctly is if a person loaded theĪrrow with the wrong vane down, they would not get a dry fire. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |